行业资讯

当前位置:网站首页 > 新闻中心 > 行业资讯

  • 无热吸干机使用情况及产品特点
  • 本站编辑:杭州天源气超滤设备工程有限公司发布日期:2018-05-17 17:07 浏览次数:
压缩热再生吸附式干燥机使用工况及技术要求:
 
额定进气压力:0.7MPa(0_5-_0_i允许使用)
 
额定进气温度:23110X:
 
空气露点:-401C(0_7MPa、-701C以下接受定制)
 
环境温度:S451C
 
压力损失:S0.02MPa
 
冷却水温:S32t:
 
再生方式:压缩余热再生
 
再生耗气量:2〇/〇耗气量(0耗气量)
 
进气含油量:客O.lmg/m3
 
安装方式:室内无基础,混凝土地平,周边留空不小于1平米
 
控制方式:全电子可编程序时间控制(露点控制)可配选
 
吸附剂:活性氧化铝+分子筛
 
 
压缩热再生吸附式千燥机机组设计特点:
 
填充GNH-280型吸千机专用分子筛
 
经久耐用的人性化设计
 
高效节能、环保、低音
 
为改善压缩空气系统的效率再生过程全部利用压缩空气本身高温的热量,吹冷阶段利用冷却水把吸
附床层的热量带出吸附塔,其综合消耗小于1%,耗电量小
 
底层采用GD-1%型活性氧化铝,上层采用GNH-28G型分子筛,气体进入吸附塔首先被底层的活性氧化铝
把大量的水份吸收,再通过上层的分子筛进行深度吸附把露点降到最低。
 
控制界面清晰明了,电源及管道连接口经考究设计安装非常方便,拥有现代化的生产设备,每一个
产品都经过严格的测试达到LX1993056的标准后才容许出厂。

The working conditions and technical requirements of compressed heat regeneration adsorption dryer are as follows:
 
Rated inlet pressure: 0.7MPa (0_5-_0_i allowed)
 
Rated intake temperature: 23110X:
 
Air dew point: -401C (0_7MPa, -701C below custom)
 
Ambient temperature: S451C
 
Pressure loss: S0.02MPa
 
Cooling water temperature: S32t:
 
Regeneration mode: compressed waste heat regeneration
 
Regenerated gas consumption: 2 gas consumption (0 gas consumption)
 
Intake of oil intake: guest O.lmg/m3
 
Installation method: indoor without foundation, concrete horizon, and the surrounding area is not less than 1 square meters.
 
Control mode: all electronic programmable time control (dew point control) can be selected.
 
Adsorbents: active alumina + molecular sieve
 
 
The design features of the compression heat regeneration adsorption type thousand dryer unit are as follows:
 
Filling GNH-280 type special molecular sieve
 
Durable humanized design
 
High efficiency, energy saving, environmental protection and bass
 
In order to improve the efficiency of the compressed air system, the regeneration process takes advantage of the high temperature of the compressed air itself.
The heat absorbed from the bed layer takes out the adsorption tower, and its comprehensive consumption is less than 1%, and the power consumption is small.
 
The bottom layer uses GD-1% type activated alumina, and the upper layer adopts GNH-28G type molecular sieve. The gas enters the adsorption tower and is activated by activated alumina at the bottom.
A large amount of water is absorbed, and then deep adsorption is carried out through the upper molecular sieve to minimize dew point.
 
The control interface is clear and clear. The connection between the power supply and the pipeline is very easy to design and install.
The products are strictly tested to reach the LX1993056 standard before they are allowed to leave the factory.

友情链接:大无限彩票开户  传奇彩票官网  大无限彩票平台  88彩票官网  幸运彩票开户  状元彩票注册  J8娱乐彩票平台  大无限彩票开户  杏彩彩票注册  J8娱乐彩票注册  

免责声明: 本站资料及图片来源互联网文章,本网不承担任何由内容信息所引起的争议和法律责任。所有作品版权归原创作者所有,与本站立场无关,如用户分享不慎侵犯了您的权益,请联系我们告知,我们将做删除处理!